Two measurements decide this mount
The RAM X-Grip Large Phone Mount with Low-Profile Tough-Claw (RAM-HOL-UN10-404-2U) is a two-part system: a medium Tough-Claw base that grips a rail, and a large X-Grip holder that grips your phone. Before you buy, check two things: the outer diameter of the rail or bar you plan to clamp onto, and the dimensions of your phone with its case, sleeve, or skin installed.
If either measurement falls outside the supported range, this kit is the wrong starting point. If both fit, the mount gives you a tool-free rail attachment and a spring-loaded X cradle with a tether for outdoor use.
Rail fit: what the Tough-Claw base clamps onto
- Round, square, and odd-shaped rails: The medium Tough-Claw base attaches to round, square, and odd-shaped rails and bars ranging from 1" to 1.6" in outer diameter. That range covers many handlebars, cart frames, and tubular rails, but not thin rods or thick oversize tubes.
- Measure the outer diameter, not the nominal size: A rail sold as 1" may measure differently once painted, wrapped, or sleeved. Use the actual outer diameter at the point where you want the claw to sit.
- Low-profile base: The low-profile Tough-Claw keeps the clamp closer to the rail than a taller base, which matters when clearance above the bar is tight.
Phone fit: the large X-Grip and your case
The large X-Grip uses an expanding X design to secure the phone, and RAM includes a device tether that is recommended for outdoor applications. The critical step is measuring your phone with its case, sleeve, or skin on, because that combined size is what the cradle actually holds.
The supplied record does not list the cradle's minimum and maximum phone dimensions, so do not assume a fit from screen size alone. Check the holder's stated dimensions against your measured phone-and-case size before ordering.
Kit facts that affect the buying decision
- RAM® X-Grip® Large Phone Mount with Low-Profile Medium Tough-Claw™: The kit consists of the medium RAM Tough-Claw base and universal large RAM X-Grip phone holder, connected by the RAM Pin-Lock adapter. The two-part design means the rail clamp and the phone holder are separate fit checks; both must work for the kit to be useful.

RAM® X-Grip® Large Phone Mount with Low-Profile Medium Tough-Claw™ - RAM® X-Grip® Large Phone Mount with Low-Profile Medium Tough-Claw™: With the Tough-Claw base connected, the mount attaches to round, square, and odd-shaped rails and bars ranging from 1" to 1.6" in outer diameter. This is the hard limit on where the mount can go; measure your rail before buying.
- RAM® X-Grip® Large Phone Mount with Low-Profile Medium Tough-Claw™: The large X-Grip features an X design that expands and contracts to secure your phone and includes a device tether recommended for outdoor applications. The tether is part of the intended outdoor setup, so plan to use it rather than treat it as an optional extra.
- RAM® X-Grip® Large Phone Mount with Low-Profile Medium Tough-Claw™: It is important to verify the dimensions of your handheld device with its case, sleeve, or skin when determining the overall size. A case can push a phone outside the cradle's supported size, so measure the combined dimensions.
Where this rail phone mount makes sense
- Bars and rails in the 1" to 1.6" range: Handlebar-style tubes, square cart frames, and irregular rails within that outer diameter are the intended targets.
- Outdoor use with a tether: The included tether is recommended for outdoor applications, so this kit suits bikes, carts, and open vehicles where a drop is possible.
- Phones that fit with their case on: Measure the phone in its everyday case; if it fits the large X-Grip's dimensions, you can keep the case on.
Trade-offs to weigh before you buy
The X-Grip cradle is a universal spring holder, not a device-specific case. That makes it flexible across phones, but it also means fit depends on your measurements rather than a model number. The Tough-Claw base is tool-free to attach, but it only works within the 1" to 1.6" rail range.
- Flexibility vs. exact fit: A universal X-Grip can hold different phones, but you must verify dimensions with the case on; a device-specific holder would not need that check.
- Tool-free clamping vs. rail limits: The Tough-Claw attaches without drilling, but rails outside 1" to 1.6" outer diameter are not supported by the supplied information.
- Tether security vs. quick removal: The tether is recommended outdoors, adding a step when you take the phone out; skipping it is a personal choice, not a manufacturer instruction.
What the supplied information does not settle
The record does not list the X-Grip's minimum and maximum phone dimensions, so you cannot confirm fit from this page alone. It also does not state whether the Pin-Lock adapter allows rotation or adjustment, or whether additional arms are needed. Check the holder's published dimensions and the rail's measured outer diameter before ordering; if either is outside the supported range, this kit is not the right choice.


